The best site ever for instructions. Your simple yet brilliant idea to construct a cradle for the jigsaw for perfect curves helped me a ton!
Thank you for your site. I have found here much useful information.
Good site ! 😉
Can i have all the dimension of your table ?
Race track, center, mainboard and rail board.
If you have plans, it will be the top.
Thanks for your response.
Main table: 6’6″ x 3’6″
Raceway: 8″ all the way around (1.5″ will be covered by rail)
Rail: 6’11” x 3’11”
4″ wide for top board. 2.5″ wide for bottom. (I made the rail after I made the table so my measurements were to fit the table, not a starting dimension)
thanks a lot !
perfect table ! Bravo “in french !”
To whom it may concern
I like your poker table so much I’ve decide to make one for myself following your instruction. But i’m stuck, I’m trying to figure out the 8 cup holders placement. I cant find them on your site. Do you think you can help me. Would be greatly appreciated. Thank you.
John
John,
It wasn’t very scientific. Basically I placed them on the sides where I wanted them to land. Then I used a flexible tape measure to evenly place them on the arc. I’m at work so I can’t tell you what the exact measurements were, but my main goal was to get 8 seats with the same table space and look right on the table. 2 on each side and 2 on each end is how it came out.
Hope that helps.
How much of the vinyl did you get for your table? I’m going to build a standard sized table. How much more do you think I’ll need for a standard sized table. Thank you very much in advance.
Also, from the prices of the plywood I’m assuming that you are using 1/2″ for the four sheets? Thanks for the help.
I used 3/4″ for the hardwood and 1/2″ for the rails.
As for the vinyl. My table is only narrowed 2 inches now that it has the whisper rails on it so I would doubt you would need more than I bought.
Hello,
Awesome diagrams and plans. My only question is tthat I’m building a standard 96″ table using the full size of an 8×4 plywood. How do you go about the railing? Do you need two separate plywood and somehow connect the two or any pieces together? Help?? Thanks in advance…..
Do you have any blackjack table plans with a race track?
The best site ever for instructions. Your simple yet brilliant idea to construct a cradle for the jigsaw for perfect curves helped me a ton!
Thank you for your site. I have found here much useful information.
Good site ! 😉
Can i have all the dimension of your table ?
Race track, center, mainboard and rail board.
If you have plans, it will be the top.
Thanks for your response.
Main table: 6’6″ x 3’6″
Raceway: 8″ all the way around (1.5″ will be covered by rail)
Rail: 6’11” x 3’11”
4″ wide for top board. 2.5″ wide for bottom. (I made the rail after I made the table so my measurements were to fit the table, not a starting dimension)
thanks a lot !
perfect table ! Bravo “in french !”
To whom it may concern
I like your poker table so much I’ve decide to make one for myself following your instruction. But i’m stuck, I’m trying to figure out the 8 cup holders placement. I cant find them on your site. Do you think you can help me. Would be greatly appreciated. Thank you.
John
John,
It wasn’t very scientific. Basically I placed them on the sides where I wanted them to land. Then I used a flexible tape measure to evenly place them on the arc. I’m at work so I can’t tell you what the exact measurements were, but my main goal was to get 8 seats with the same table space and look right on the table. 2 on each side and 2 on each end is how it came out.
Hope that helps.
How much of the vinyl did you get for your table? I’m going to build a standard sized table. How much more do you think I’ll need for a standard sized table. Thank you very much in advance.
Also, from the prices of the plywood I’m assuming that you are using 1/2″ for the four sheets? Thanks for the help.
I used 3/4″ for the hardwood and 1/2″ for the rails.
As for the vinyl. My table is only narrowed 2 inches now that it has the whisper rails on it so I would doubt you would need more than I bought.
Hello,
Awesome diagrams and plans. My only question is tthat I’m building a standard 96″ table using the full size of an 8×4 plywood. How do you go about the railing? Do you need two separate plywood and somehow connect the two or any pieces together? Help?? Thanks in advance…..
Do you have any blackjack table plans with a race track?